Two Door Selection Guide

ABB Controls Disconnect switch: Flange operated switch (fusible or non-fusible) Shaft: 12.13" deep enclosures use  DSFHS-12 18.13" deep enclosures use  DSFHS-17 24.13" deep enclosures, platform must be used with shaft (not included) Handle: DSFHN-HS12   Circuit breaker: Circuit breaker: ABB Operating mechanism Shaft: 12.13" deep enclosures use  K7FHD-S12 18.13" deep enclosures use  K7FHD-S17 24.13" deep enclosures, platform must be used with shaft (not included) Handle mechanism: K7FHD-HS12    Allen Bradley Bulletin 1494F flange mounted disconnect switch: Disconnect switch Fuse block adaptor (if required) Line and load connectors (if required)   1494D flange mounted circuit breaker operating mechanism, order: Circuit breaker: C-H Westinghouse Operating mechanism Slide mechanism   Bulletin 1494U flange mounted disconnect switch, order: Disconnect switch Operating handle Connecting rod (long) Trailer fuse block kit (if required) Fuse kit (if required) Line and load connectors (if required)   Bulletin 1494U flange mounted circuit breaker operating mechanism, order: Circuit breaker: C-H Westinghouse Operating mechanism Operating handle Connecting rod (long) When Allen Bradley 1494U devices are installed in 72" high enclosures with the operating handle mounted on the center post, an optional Allen Bradley channel support kit is recommended.

C-H Westinghouse Type C361 disconnect switch: Disconnect switch with an operating mechanism Operating handle: C361H1 or C361H3 In 24.13" deep enclosures, platform must be used with shaft (not included)   Type C371 circuit breaker operating mechanism with a C-H Westinghouse circuit breaker: Circuit breaker Operating mechanism Long operating rod (if required) Operating handle: 150 amp - C371H1 or C371H3 250 through 600 amp - C371H5 or C371H7   Flex-Shaft™ handle mechanism: Circuit breaker Complete Flex-Shaft™ handle mechanism   General Electric Disconnect switch: Disconnect switch: Type QMR or QMW Fuse clip kit or no-fuse kit Flange handle: STDA1 or STDA2 Variable depth operating mechanism Extended length drive rod (if required)   Circuit breaker: Circuit breaker Flange handle: STDA1 or STDA2 Variable depth operating mechanism Extended length drive rod (if required) An optional General Electric Flange Stiffener Kit (TDSR) is recommended when General Electric Type TDA devices are installed in 72.13" high enclosures with operating handle mounted on centerpost. Use with TDOM1, TDOM2, TDOM3, S100M1A, and S100M3 operating mechanisms.    Circuit breaker with a Spectra-Flex™ cable operator: Circuit breaker Flange mounted handle mechanism: 150 to 600 amps - STDA1 SK1200 - STDA3 Breaker mounted mechanism Operating cable

I-T-E Siemens Disconnect switch: Basic switch (right-hand) Fuse or no-fuse kit Flange mounted handle: FHOHS Switch operator Operating cable: FHOEC036 cable for 12.13" deep FHOECO48 for 18.13" and 24.13" deep enclosures   Circuit breaker: Circuit breaker Pressure wire connectors Flange mounted handle: 100 to 600 - FHOH 800 to 2000 - FHOHN Circuit breaker operator mechanism Operating cable: 36" cable for 12.13" or 18.13" deep 48" for 24.13" deep enclosures These items are available from Siemens I-T-E as a complete mechanism with a 36" operating cable only Order items separately when using a 48" cable   Square D Disconnect switch: Disconnect switch with operating mechanism Universal handle mechanism: Type A-1 Long operating rod (if required)   Circuit breaker: Circuit breaker Operating mechanism Universal handle mechanism: Type A-1 Long operating rod (if required)   Class 9422 Type T disconnect switch with a cable mechanism: Disconnect switch with operating mechanism: Class 9422, Type T Handle mechanism: Class 9422, Type A-1 Cable mechanism: Class 9422 CFT_O, 3, 5, or 10 foot   Circuit breaker with a cable mechanism: Circuit breaker: Square D Handle mechanism: Class 9422, type A-1 Cable mechanism: Class 9422 CFT_O, 3, 5, or 10 foot An optional Square D Channel flange Support Kit (9422-C1) is recommended when some Square D devices are installed in 72.13" high enclosures with operating handle mounted on centerpost.

ABB Controls

ABB Controls Disconnect Switches (Flange Mounted Operators)

Fits Enclosure Height		ABB Switch  Number	Amp				Space  Occupied		When  A=60.13 P	When  A=72.13 P
60.13	72.13		Rating	Fuse Clip	Fuse Class	L	M	N
•	•	OETL-NF30-F	30A	No Fuse	—	4.45	3.91	0.25	9.53	15.53
•	•	OETL-NF60-F	60A	No Fuse	—	4.86	3.91	0.25	9.34	15.34
•	•	OETL-NF100-F	100A	No Fuse	—	4.86	4.91	0.25	8.78	14.78
•	•	OETL-NF175-F	175A	No Fuse	—	7.30	6.62	0.25	6.53	12.53
•	•	OETL-NF200-F	200A	No Fuse	—	7.36	7.41	0.25	6.53	12.53
•	•	OESA-F30J6-F	30A	30A-600V	J	4.28	6.70	0.25	7.85	13.86
•	•	OESA-F60J6-F	60A	60A-600V	J	4.28	6.39	0.25	7.85	13.86
•	•	OESA-F100J6-F	100A	100A-600V	J¹	6.54	7.78	0.25	7.42	13.42
			200A²

¹ J type fuse clips are standard. If 600 V Type “T” fuse clips are desired order T type fuse adaptor kit.
² 200 A available by using non-fusible 200A switch and a trailing fuse block. (consult ABB)   ABB Controls Circuit Breaker (Flange Mounted Operators)

Fits Enclosure Height		ISOMAX Circuit Breaker	Amp  Rating	Operating  Mechanism	Frame  Type	Space Occupied			When  A=60.13 P	When  A=72.13 P
60.13	72.13					L	M	N
•	•	S1N100TL	100A	K2FHD-M	S1	5.30	4.60	0.63	8.33	14.33
•	•	S3N150TW	150A	K3FHD-M	S3	6.67	5.02	0.63	7.73	13.73
•	•	S3N225TW	225A	K3FHD-M	S3	6.67	5.02	0.63	7.73	13.73
•	•	S4N250BW	250A	K4FHD-M	S4	8.45	5.02	0.63	6.20	12.20
•	•	S5N400TW	400A	K5FHD-M	S5	8.45	6.40	0.63	6.20	12.20
•	•	S6N600TW	600A	K6FHD-M	S6	8.33	10.00	0.63	5.53	11.53
•	•	S6N800TW	800A	K6FHD-M	S6	8.33	10.00	0.63	5.53	11.53

"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13 Charts reference Space Occupied by Disconnect Drawing.  

Allen Bradley

Allen Bradley 1494F Disconnect Switches

Fits Enclosure Height		Allen Bradley Switch  Number	Amp  Rating				Space  Occupied M¹		When  A=60.13 P	When  A=72.13 P
60.13	72.13			Fuse Clip	Fuse Class	L		N
•	•	N30	30A	No Fuse	—	4.62	6.50	0.63	5.31	11.31
•	•	NF30	30A	30A-250V	H, K, R	6.50	6.50	0.63	5.31	11.31
•	•	NF30	30A	60A-250V	H, K, R	7.25	6.50	0.63	5.31	11.31
•	•	NF30	30A	30A-600V	H, K, R	9.25	6.50	0.63	5.31	11.31
•	•	NF30	30A	60A-600V	H, K, R	9.75	6.50	0.63	5.31	11.31
•	•	NF30	30A	30A-600V	J	6.50	6.50	0.63	5.31	11.31
•	•	NF30	30A	60A-600V	J	6.62	6.50	0.63	5.31	11.31
•	•	N60	60A	No Fuse	—	4.62	6.50	0.63	4.62	10.62
•	•	NF60	60A	30A-600V	H, K, R	10.38	6.50	0.63	4.62	10.62
•	•	NF60	60A	60A-250V	H, K, R	8.38	6.50	0.63	4.62	10.62
•	•	NF60	60A	100A-250V	H, K, R	10.88	6.50	0.63	4.62	10.62
•	•	NF60	60A	60A-600V	H, K, R	10.88	6.50	0.63	4.62	10.62
•	•	NF60	60A	100A-600V	H, K, R	12.88	6.62	0.63	4.62	10.62
•	•	NF60	60A	60A-600V	J	7.75	6.50	0.63	4.62	10.62
•	•	NF60	60A	100A-600V	J	9.75	6.50	0.63	4.62	10.62
	•	N100	100A	No Fuse	—	4.62	7.25	0.63	—	8.75
	•	NF100	100A	100A-250V	H, K, R	11.38	7.38	0.63	—	8.75
	•	NF100	100A	200A-250V	H, K, R	12.25	7.62	0.63	—	8.75
	•	NF100	100A	100A-600V	H, K, R	13.38	7.50	0.63	—	8.75
	•	NF100	100A	200A-600V	H, K, R	14.75	7.75	0.63	—	8.75
	•	NF100	100A	100A-600V	J	10.12	7.38	0.63	—	8.75
	•	NF100	100A	200A-600V	J	10.88	7.50	0.63	—	8.75
	•	N200	200A	No Fuse	—	7.12	10.38	0.56	—	7.13
	•	NF200	200A	200A-250V	H, K, R	15.00	10.38	0.56	—	7.13
	•	NF200	200A	400A-250V	H, K, R	16.56	10.75	0.56	—	7.13
	•	NF200	200A	200A-600V	H, K, R	17.56	10.38	0.56	—	7.13
	•	NF200	200A	400A-600V	H, K, R	19.56	11.00	0.56	—	7.13
	•	NF200	200A	200A-600V	J	13.69	10.38	0.56	—	7.13
	•	NF200	200A	400A-600V	J	15.00	10.62	0.56	—	7.13

¹"M" dimension does not allow for auxiliary switches. Refer to Allen Bradley instructions if additional space is required.  

Allen Bradley 1494D Operators (Circuit Breakers)

Fits Enclosure Height		Alan Bradley  Type Number	Amp  Rating	Circuit Breker Type		Space Occupied		When  A=60.13 P	When  A=72.13 P
60.13	72.13				L	M¹	N
•	•	N4/N40	150A	C-H Westinghouse  EHD,FD,FDB,FDC,HFD,HMCP	5.81	4.56	0.63	5.25	11.25
•	•	N5/N55	225A	General Electric  TFK, THFK, TFC	8.81	4.75	0.63	4.44	10.44
•	•	N5/N50	250A	C-H Westinghouse JD,JDB,JDC,HJD,HMCP	8.81	4.75	0.63	4.44	10.44
	•	N5/N60	400A	C-H Westinghouse  KD,KDB,DK,HKD,HMCP	8.81	5.88	0.63	—	10.50

1 "M" dimension does not allow for auxiliary switches. Refer to Allen Bradley instructions if additional space is required.
"K" = 5.88 when "A" = 60.13
"K" = 11.88 when "A" = 72.13 (except 200A switches)
"K" = 10.56 when "A" = 72.13 (200A switches only).  

Allen Bradley 1494U Operators (Disconnect Switches)

Fits Enclosure Height		Alan Bradley Switch Number	Amp				Space  Occupied		When  A=60.13 P	When  A=72.13 P
60.13	72.13		Rating	Fuse Clip	Fuse Class	L	M²	N
•	•	DS30	30A	No Fuse	—	3.88	6.75	1.06	6.00	12.00
•	•	DS30	30A	30A-250V	H,K,R	5.25	6.75	1.06	6.00	12.00
•	•	DS30	30A	30A-600V	H,K,R	8.00	6.75	1.06	6.00	12.00
•	•	DS30	30A	30A-600V	J	5.25	6.75	1.06	6.00	12.00
•	•	DS30	30A	60A-250V	H,K	6.00	6.75	1.06	6.00	12.00
•	•	DS30	30A	60A-600V	H,K	8.50	6.75	1.06	6.00	12.00
•	•	DS30	30A	60A-600V	J	5.38	6.75	1.06	6.00	12.00
•	•	DS60	60A	No Fuse	—	3.88	6.75	1.06	5.81	11.81
•	•	DS60	60A	60A-250V	H,K,R	6.00	6.75	1.06	5.81	11.81
•	•	DS60	60A	60A-600V	H,K,R	8.50	6.75	1.06	5.81	11.81
•	•	DS60	60A	60A-600V	J	5.38	6.75	1.06	5.81	11.81
•	•	DS60	60A	30A-600V	H,K,R	8.00	6.75	1.06	5.81	11.81
•	•	DS60	60A	100A-250V	H,K	8.50	6.75	1.06	5.81	11.81
•	•	DS60	60A	100A-600V	H,K	10.50	6.75	1.06	5.81	11.81
•	•	DS60	60A	100A-600V	J	7.25	6.75	1.06	5.81	11.81
•	•	DS100¹	100A	No Fuse	—	3.88	6.75	1.06	5.81	11.81
•	•	DS100¹	100A	100A-250V	H,K,R	8.12	6.75	1.06	5.81	11.81
•	•	DS100¹	100A	100A-600V	H,K,R	10.12	6.75	1.06	5.81	11.81
•	•	DS100¹	100A	100A-600V	J	6.80	6.75	1.06	5.81	11.81
•	•	DS100¹	100A	60A-600V	H,K,R	10.12	6.75	1.06	5.81	11.81
•	•	DS100¹	100A	60A-600V	J	8.88	6.75	1.06	5.81	11.81
	•	DS2001	200A	No Fuse	—	4.75	8.00	1.06	—	10.34
	•	DS2001	200A	200A-250V	H,K,R	10.88	8.00	1.06	—	10.34
	•	DS2001	200A	200A-600V	H,K,R	13.88	8.00	1.06	—	10.34
	•	DS2001	200A	200A-600V	J	9.50	8.00	1.06	—	10.34
	•	DS2001	200A	100A-600V	H,K,R	12.00	8.00	1.06	—	10.34
	•	DS2001	200A	100A-600V	J	8.75	8.00	1.06	—	10.34

1 Series B
2 "M" dimension does not allow for auxiliary switches  

Allen Bradley 1494U Operators (Circuit Breakers)

Fits Enclosure Height		Alan Bradley Type Number	Amp			Space  Occupied		When  A=60.13 P	When A=72.13 P
60.13	72.13		Rating	Circuit Breker Type	L	M1	N
•	•	M40	15A-150A	C-H Westinghouse  EHD,FD,FDB,FDC,HFD,HMCP	5.00	4.62	1.06	7.25	13.25
•	•	M50	70A-250A	C-H Westinghouse  JD,JDB,JDC,HJD,HMCP	9.75	4.88	1.06	6.81	12.81
	•	M60	100A-400A	C-H Westinghouse  KD,KDB,DK,HKD,HMCP	9.69	6.25	1.06	—	12.62

1 "M" dimension does not allow for auxiliary switches. Refer to Allen Bradley instructions if additional space is required.
"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13  

Cutler Hammer

Cutler Hammer C361 Disconnect Switches

Fits Enclosure Height		Cutler Hammer Type Number	Amp				Space  Occupied		When  A=60.13 P	When  A=72.13 P
60.13	72.13		Rating	Fuse Clip	Fuse Class	L	M	N
•	•	C361NC	30A	No Fuse	—	5.75	7.55	0.63	6.50	12.50
•	•	C361SC21	30A	30A-250V	H, K, R	8.38	7.55	0.63	6.50	12.50
•	•	C361SC61	30A	60A-250V	H, K, R	8.38	7.55	0.63	6.50	12.50
•	•	C361SC61	30A	30A-600V	H, J, K, R	8.38	7.55	0.63	6.50	12.50
•	•	C361ND	60A	No Fuse	—	5.75	7.55	0.63	6.50	12.50
•	•	C361SD22	60A	60A-250V	H, K, R	8.38	7.55	0.63	6.50	12.50
•	•	C361SD22	60A	30A-600V	J	8.38	7.55	0.63	6.50	12.50
•	•	C361SD62	60A	60A-600V	H, K, R	8.38	7.55	0.63	6.50	12.50
•	•	C361SD62	60A	60A-600V	J	8.38	7.55	0.63	6.50	12.50
•	•	C361NE	100A	No Fuse	—	5.56	9.07	0.63	6.06	12.06
•	•	C361SE263	100A	100A-250V	H, K, R	10.31	9.07	0.63	6.06	12.06
•	•	C361SE263	100A	100A-600V	H, K, R	10.31	9.07	0.63	6.06	12.06
•	•	C361SE263	100A	100A-600V	J	10.31	9.07	0.63	6.06	12.06
•	•	C361NF	200A	No Fuse	—	13.06	10.12	0.63	4.06	10.12
•	•	C361SF264	200A	200A-250V	H, K, R	13.06	10.12	0.63	4.06	10.12
•	•	C361SF264	200A	200A-600V	H, K, R, J	13.06	10.12	0.63	4.06	10.12

  Cutler Hammer C371 Circuit Breaker (C-H Westinghouse Circuit Breakers)

Fits Enclosure Height		Cutler Hammer  Mechanisms	Amp			Space Occupied		When  A=60.13 P	When  A=72.13 P
60.13	72.13		Rating	Frame Type	L	M	N
•	•	C371E	150A	F Frame EHD,FDB,FD,HFD,FDC	6.00	5.62	0.63	7.62	13.62
•	•	C371E	150A	F Frame HMCP	6.00	5.62	0.63	7.62	13.62
¹	•	C371F	250A	J Frame JDB,JD,HJD,JDC	8.94	8.12	0.63	7.50	13.50
¹	•	C371F	250A	J Frame HMCP	10.94	8.12	0.63	7.50	13.50
¹	•	C371F	400A	K Frame DK,KDB,KD,HKD	9.75	8.12	0.63	7.00	13.00
¹	•	C371F	400A	K Frame HMCP	9.75	8.12	0.63	7.00	13.00
	²	C371G	600A	L Frame LD,HLD,LDC	8.44	12.00	0.63	-	11.38
	²	C371G	600A	L Frame HMCP	8.44	12.00	0.63	-	11.38

1Wire bend space "P" does not allow cable size larger than 4/0 AWG in a 60.13" tall enclosures.
2Wire bend space "P" does not allow cable size larger than 300 MCM.
"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13
Charts reference Space Occupied by Disconnect Drawing.   Cutler Hammer Flex-Shaft™ Operator Mechanisms (C-H Westinghouse Circuit Breakers)

Complete Operator			Breaker Height "X"	Breaker Width "Y"
Mechanisms	Amp  Rating	Frame Type	(in inches)	(in inches)
F1S03	150A	F Frame EHD,FDB,FD,HFD	6.00	4.12
F1S03	150A	F Frame HCMP	6.00	4.12
F2S03	250A	J  Frame JDB,JD,HJD,JDC	10.00	4.12
F2S03	250A	J  Frame HCMP	10.00	4.12
F3S03	400A	K  Frame DK,KDB,KD,HKD	10.12	5.50
F3S03	400A	K  Frame HCMP	12.45	5.50
F4S04	600A	L  Frame LD,HLD,LDC	10.75	8.25
F7S04	800A	M Frame MD,MDS	16.00	8.25
F5S04	1200A	N Frame ND,HND,NDC	16.00	8.25
F6S04	2500A	R Frame RD,CRD, RDC	16.00	15.50

Part numbers for Complete Operator Mechanisms include flange mounted handle, flexible shaft and circuit breaker mechanism.
The last digit of the part number denotes the shaft length (F1S03=3' length). 
F,J,K frame Flex-Shafts™ available in 3' to 10' lengths.
L,N,R frame Flex-Shafts™ available in 4' to 6' lengths.

Space Occupied By Disconnect
1. Flex-Shaft™ System permits circuit breaker locations separate from flange mounted handle mechanism.
2. See National Electrical Code 2005 article 430-10(b) for wiring space (Ref "P") needed for line side conductors.
3. Select shaft length based on location of circuit breaker in the enclosure. Maintain a 4" minimum bending radius for the Flex-Shaft™.
4. Space occupied by circuit breaker is calculated by:

• Overall (Height "X" and Width "Y")
• Minimum wire bend space (manufacturer specified)
• Location "M" from right to left.

Charts reference Space Occupied by Disconnect Drawing

      General Electric 

General Electric Type STDA Disconnect Switche Operators  

Fits Enclosure Height		General Electric  Switch Mechanisms	Amp  Rating				Space  Occupied M		When  A=60.13 P	When  A=72.13 P
60.13	72.13			Fuse Clip	Fuse Class	L		N
•	•	TDOM1A	30A	No Fuse	-	6.88	5.38	0.63	8.38	14.38
•	•	TDOM1A	30A	30A-250V	H, R	6.88	5.38	0.63	8.38	14.38
•	•	TDOM1B	30A	30A-600V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	30A	60A-250V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	30A	60A-600V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1A	60A	No Fuse	-	6.88	5.38	0.63	8.38	14.38
•	•	TDOM1B	60A	60A-250V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	60A	60A-600V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	60A	100A-250V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	60A	100A-600V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1A	100A	No Fuse	-	6.88	5.38	0.63	8.38	14.38
•	•	TDOM1B	100A	100A-250V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	100A	100A-600V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	100A	200A-250V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM1B	100A	200A-600V	H, R	11.5	5.38	0.63	8.38	14.38
•	•	TDOM2	200A	No Fuse	-	7	9.25	0.63	5.69	11.69
•	•	TDOM2	200A	200A-250V	H, R	15.38	9.25	0.63	5.69	11.69
•	•	TDOM2	200A	200A-600V	H, R	15.38	9.25	0.63	5.69	11.69

      General Electric Type STDA Circuit Breaker Operators  

Fits Enclosure Height		General Electric  Circuit Breaker Mechanisms	Amp  Rating	Frame Type		Space Occupied		When  A=60.13 P	When  A=72.13 P
60.13	72.13				L	M	N
•	•	TDOM1A	150A	TEB, TED, THED	6.88	5.38	0.63	7.24	13.24
•	•	TDOM1A	150A	TEC	6.88	5.38	0.63	7.24	13.24
•	•	TDOM1B	150A	TB1	11.50	5.38	0.63	7.24	13.24
•	•	TDOM1B	150A	TEC, TECL	11.50	5.38	0.63	7.24	13.24
•	•	TDOM1C	150A	TEL	6.88	5.38	0.63	7.24	13.24
•	•	TDOM1D	150A	THLC1	6.88	5.38	0.63	5.87	11.87
•	•	TDOM3	225A	TFJ	10.38	5.88	0.63	6.81	12.81
•	•	TDOM3	225A	TFK, THFK, TFL	10.38	5.88	0.63	6.81	12.81
	•	TDOM4	400A	TJJ, TJK4, THJK4, TJL4V	8.25	9.50	0.63	—	11.91
	•	TDOM4	600A	TJK6, THJK6, TJ4V, TJL4V	8.25	9.50	0.63	—	11.91
	•	TDOM5	400A	TB4, TJH6S	14.25	9.50	0.63	—	11.91
	•	TDOM6	225A	TLB2, THLC2	11.75	9.50	0.63	—	11.35
	•	TDOM6	400A	TLB4, THLC4	11.75	9.50	0.63	—	9.97
•	•	SDOM1A	150A	SE150	6.88	5.38	0.63	7.24	13.24
•	•	SDOM3	250A	SPECTRA SF250	10.38	5.88	0.63	6.81	11.88
	•	SDOM4	600A	SPECTRA SG600	10.00	7.12	0.63	—	9.18

"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13       General Electric Circuit Breakers (Spectra-Flex™ Cable Operators)  

Fits Enclosure Height				Circuit Breaker Height	Circuit Breaker Width
60.13	72.13	Frame Size	Max Amp Rating	"X"	"Y"
•	•	E150	150A	6.31	4.12
•	•	SE150	150A	6.31	4.12
•	•	SF250	250A	10.12	4.12
•	•	SG600	600A	10.09	5.50
•	•	SK1200	1200A	15.50	8.25

Note: All 2UD,2UDF,2UDCP series enclosures that are 24.00" deep require a 48" or longer operating cable
 

Frame Size	Breaker Mechanism	Flange Mounting Handle¹	Operating Cable²
E150	SCOM1A	SCH1	SC3L
SE150/SF250	SCOM1EF	SCH1	SC3L
SG600	SCOM1G	SCH1	SC3L
SK1200	SCOM1K	SCH2K	SC3H

1Add "X" for NEMA 4 or NEMA 4X Flange mounting handle.
2Operating Cables are available 3' to 10' lengths. In the table above, the number "3" in the part number indicates a 3' cable.

Space Occupied By Disconnect
1. GE Spectra-Flex™ Operating Cables permit circuit breaker locations separate from flange mounted handle mechanism.
2. See National Electrical Code 2005 article 430-10(b) for wiring space (Ref "P") needed for line side conductors.
3. Select shaft length based on location of circuit breaker in the enclosure. Maintain a 3" minimum bending radius for the Flex-Shaft™.
4. Space occupied by circuit breaker is calculated by:
Overall (Height "X" and Width "Y")
Minimum wire bend space (manufacturer specified)
Location "M" from right to left.

"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13

Charts reference Space Occupied by Disconnect Drawing.

Siemens I-T-E 

I-T-E - Disconnect Switches (Max-Flex™ Operators)  

Fits Enclosure Depth			Amp			Disconnect Height  "X"	Disconnect Width  "Y"
60.13	72.13	Switch	Rating	Fuse Clip	Fuse Class
•	•	MCS603R	30A	No Fuse	—	5.52	6.13
•	•	MCS603R	30A	30A-250V	H,K,R	8.11	6.13
•	•	MCS603R	30A	30A-600V	H,K,R	10.11	6.13
•	•	MCS603R	30A	30A-600V	J	8.48	6.13
•	•	MCS606R	60A	No Fuse	—	5.52	6.13
•	•	MCS606R	60A	60A-250V	H,K,R	7.86	6.13
•	•	MCS606R	60A	60A-600V	H,K,R	10.38	6.13
•	•	MCS606R	60A	60A-600V	J	8.36	6.13
•	•	MCS610R	100A	No Fuse	—	7.59	7.38
•	•	MCS610R	100A	100A-250V	H,K,R	11.85	7.38
•	•	MCS610R	100A	100A-600V	H,K,R	13.85	7.38
•	•	MCS610R	100A	100A-600V	J	10.60	7.38
•	•	MCS620R	200A	No Fuse	—	9.00	9.17
•	•	MCS620R	200A	200A-250V	H,K,R	14.70	9.17
•	•	MCS620R	200A	200A-600V	H,K,R	17.20	9.17
•	•	MCS620R	200A	200A-600V	J	13.32	9.17

Note: Enclosures that are 24.13" deep require a 48" Max-Flex™ cable (minimum cable length).       Siemens I-T-E Max-Flex™ Operators (Circuit Breakers)  

Complete Operator  Mechansim	Amp Rating	Breaker  Frame Size		Circuit Breaker Height "X"	Circuit Breaker Width "Y"
			Circuit Breaker Type
FHOE036	125A	ED	ED2, ED4, ED6, HED4, HED6	6.34	3.00
FHOE036	125A	CED	CED6	9.58	3.00
FHOF036	250A	FD	FXD6-A, FD6-A, HFD6, FXD6ETJ, HHFD6, HHFXD6	9.50	4.50
FHOF036	250A	CFD	CFD6, CFD6-ETI	14.25	4.50
FHOJ036	400A, 600A	JD, LD	JXD2, LXD6, JD6, LD6, HJD6, HLD6, HHJD6, HHLD6,  HHJXD6, HHLDX6, JXD6-ETI, LXD6-ETI	11.00	7.50
FHOJ036	400A, 600A	CJD,CLD	CJD6, CLD6, CJD6-ETI, CLD6-ETI	17.86	7.50
FHOLMO36	800A	LMD	LMD6, LMXD6, HLMD6, HLMXD6, LMXD6-ETI	16.00	9.00
FHON048	800A, 1200A	MD, ND	MD6, ND6, MXD6, NXD6, HMD6, HND6, HMXD6, HNXD6, CMD6, CND6, MXD6-ETI, CMD6-ETI	24.00	9.00
FHONO48	1600A, 2000A	PD,RD	PD6, RD6, PXD6, RXD6, HPD6, HRD6, HPXD6,  HRXD6, CPD6	24.50(2)	13.63(2)

Circuit Breaker Size includes required base mounting block.
Last three digits of operator mechanism part number denote cable length in inches. 
24" deep enclosures require longer operating cables. Sold separately.
"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13
(Deduct 1.45 inches from "K" for FHONO48 Operator mechanism for MD,ND,PD,RD Circuit Breakers)

Space Occupied By Disconnect
1. Siemens I-T-E Max-Flex™ System permits circuit breaker locations separate from flange mounted handle mechanism.
2. See National Electrical Code 2005 article 430-10(b) for wiring space (Ref “P”) needed for line side conductors.
3. See Siemens I-T-E instructions for disconnect location limitations when using 36" or 48" Max-Flex™ cables.
4. Space occupied by circuit breaker is calculated by:

• Overall (Height "X" and Width "Y")
• Minimum wire bend space (manufacturer specified)
• Location "M" from right to left.

Charts reference Space Occupied by Disconnect Drawing.

Square D

Square D Class 9422 Variable Depth Disconnect Switches  

Fits Enclosure Height		Square D  Amp Number	Amp Rating			Space Occupied			When  A=60.13 P	When  A=72.13 P
60.13	72.13			Fuse Clip	Fuse Class	L	M	N
•	•	TCN-30	30A	No Fuse	—	3.80	6.97	0.63	6.75	12.75
•	•	TCF-30	30A	30A-250V	H, K, R	5.53	6.97	0.63	6.75	12.75
•	•	TCF-33	30A	30A-600V	H, K, R	8.15	6.97	0.63	6.75	12.75
•	•	TCF-33	30A	60A-250V	H, K, R	6.15	6.97	0.63	6.75	12.75
•	•	TCF-33	30A	30A-600V	J	5.53	6.97	0.63	6.75	12.75
•	•	TDN-60	60A	No Fuse	—	3.80	6.97	0.63	6.75	12.75
•	•	TDF-60	60A	30A-600V	H, K, R	8.15	6.97	0.63	6.75	12.75
•	•	TDF-60	60A	60A-250V	H, K, R	6.15	6.97	0.63	6.75	12.75
•	•	TDF-63	60A	60A-600V	H, K, R	8.65	6.97	0.63	6.75	12.75
•	•	TDF-63	60A	60A-600V	J	5.53	6.97	0.63	6.75	12.75
•	•	TEN-10	100A	No Fuse	—	3.80	6.97	0.63	6.62	12.62
•	•	TEF-10	100A	100A-250V	H, K, R	8.25	6.97	0.63	6.62	12.62
•	•	TEF-10	100A	100A-600V	H, K, R	10.25	6.97	0.63	6.62	12.62
•	•	TEF-10	100A	100A-600V	J	7.05	6.97	0.63	6.62	12.62
•	•	TEF-13	100A	200A-600V	J	—	—	0.63	6.62	12.62
•	•	TC-1	30A	No Fuse	‑	5.75	6.12	0.63	5.88	11.88
•	•	TC-2	30A	30A-250V	H, K, R	5.75	6.12	0.63	5.88	11.88
•	•	TC-3	30A	30A-600V	H, K, R	7.75	6.12	0.63	5.88	11.88
•	•	TC-3	30A	60A-250V	H, K, R	5.88	6.12	0.63	5.88	11.88
•	•	TC-3	30A	30A-600V	J	5.75	6.12	0.63	5.88	11.88
•	•	TD-1	60A	No Fuse	—	6.38	6.75	0.63	6.75	12.75
•	•	TD-2	60A	30A-600V	H, K, R	8.50	6.75	0.63	6.75	12.75
•	•	TD-2	60A	60A-250V	H, K, R	6.50	6.75	0.63	6.75	12.75
•	•	TD-3	60A	60A-600V	H, K, R	9.00	6.75	0.63	6.75	12.75
•	•	TD-3	60A	60A-600V	J	6.38	6.75	0.63	6.75	12.75
•	•	TE-1	100A	No Fuse	—	4.75	8.50	0.63	6.50	12.50
•	•	TE-2	100A	100A-250V	H, K, R	7.50	8.50	0.63	6.50	12.50
•	•	TE-2	100A	100A-600V	H, K, R	9.50	8.50	0.63	6.50	12.50
•	•	TE-2	100A	100A-600V	J	6.25	8.50	0.63	6.50	12.50
•	•	TE-3	100A	200A-600V	J	13.75	8.50	0.63	6.50	12.50
•	•	TF-1	200A	No Fuse	—	5.50	11.75	0.63	5.12	11.12
•	•	TF-2	200A	200A-250V	H, K, R	11.50	11.75	0.63	5.12	11.12
•	•	TF-2	200A	200A-600V	H, K, R	14.00	11.75	0.63	5.12	11.12
•	•	TF-2	200A	200A-600V	J	10.12	11.75	0.63	5.12	11.12
•	•	TF-3	200A	400A-600V	J	14.50	11.75	0.63	5.12	11.12

      Square D Class 9422 Variable Depth Operators (Circuit Breakers)  

Fits Enclosure Depth		Square D Type  Number	Amp  Rating		Space Occupied			When  A=60.13 P	When  A=72.13 P
60.13	72.13			Frame Size	L	M	N
•	•	RG-1	75A	GJL	3.53	3.87	0.63	6.69	12.69
•	•	RG-1	100A	GJL	3.53	3.87	0.63	6.69	12.69
•	•	RN-1	100A	FAL, FHL	5.12	5.38	0.63	6.88	12.88
•	•	RP-1	250A	KAL, KHL	7.12	5.75	0.63	7.56	13.56
	•	RR-1	400A	LAL, LHL, Q4L	7.62	8.88	0.63	—	9.25

"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13

Charts reference Space Occupied by Disconnect Drawing.

      Square D Class 9422 Disconnect Switches (Cable Mechanism 9422-CFT30 and 9422A-1 Handle Mechanism)  

Fits Enclosure Depth		Square D  Type Number	Amp  Rating	Fuse Clip	Fuse Class	Disconnect Height  "X"	Disconnect Width  "Y"
A=60.13	A=72.13
P	P
•	•	TCN-30	30A	No Fuse	—	5.90	6.20
•	•	TCF-30	30A	30A-250V	H, K, R	7.50	6.20
•	•	TCF-33	30A	30A-600V	H, K, R	10.15	6.20
•	•	TCF-33	30A	60A-250V	H, K, R	8.15	6.20
•	•	TCF-33	30A	30A-600V	J	7.50	6.20
•	•	TDN-60	60A	No Fuse	—	5.90	6.20
•	•	TDF-60	60A	30A-600V	H, K, R	10.15	6.20
•	•	TDF-60	60A	60A-250V	H, K, R	8.15	6.20
•	•	TDF-63	60A	60A-600V	H, K, R	10.65	6.20
•	•	TDF-63	60A	60A-600V	J	7.50	6.20
•	•	TEN-10	100A	No Fuse	—	5.90	6.20
•	•	TEF-10	100A	100A-250V	H, K, R	10.35	6.20
•	•	TEF-10	100A	100A-600V	H, K, R	10.35	6.20
•	•	TEF-10	100A	100A-600V	J	10.35	6.20

      Square D Class 9422 Cable Mechanism (Circuit Breakers)  

Fits Enclosure Depth
A=60.13	A=72.13				Circuit Breaker	Circuit Breaker
P	P	Cable Type Switch	Amp Rating	Frame Type	Height "X"	Width "Y"
•	•	9422 CGJ30	75A	GJL	4.75	3.50
•	•	9422 CEJ30	100A	GJL	4.75	3.50
•	•	9422 CFA30	100A	FAL,FHL	6.00	4.50
•	•	9422 CKA30	250A	KAL,KHL	8.00	4.50
•	•	9422 CLA30	400A	LAL,LHL,Q4L	11.00	6.00

Use cable mechanism with circuit breaker and 9422-A1 handle mechanism
Cable operators are offered in 3’, 5’, and 10’ lengths. Last 2 digits of part numbers above (30) are for 3’ cables

Space Occupied By Disconnect Switch
1. Square D Cable System permits circuit breaker locations separate from flange mounted handle mechanism.
2. See National Electrical Code 2005 article 430-10(b) for wiring space (Ref “P”) needed for line side conductors.
3. Select cable mechanism length based on disconnect location in enclosure. See Square D instructions for minimum cable bend radius.
4. Space occupied by circuit breaker is calculated by:

 

• Overall (Height "X" and Width "Y")
• Minimum wire bend space (manufacturer specified)

"K" = 7.88 when "A" = 60.13
"K" = 13.88 when "A" = 72.13

Charts reference Space Occupied by Disconnect Drawing.